Industrial Visit of Final Year Electrical at Expel Prosys, Manjusar on 30/07/16

All the interested students for this visit shall get register and send their details by 28/7/16 to Prof. P.K.Shah/Prof. A.K.Giri for Industrial visit at Expel Prosys Ltd on 30/07/16

Registered students shall meet Prof. P.K.Shah for exact route map for travelling to industry.

Starting point: Pandya Bridge, Near M.S.U polytecnic, Vadodara (Near to railway and Bus station, Vaddodara), Sharp at 9.30 A.M

Second Stop would be amit nagar circle, V.I.P road, Vadodara.

Then we will depart to manjusar, savli route from Dhumar chowkdi. We have to reach industry sharp at 10.45 a.m on 30/07/16

Address:
Expel Prosys

PLOT NO.: 347, MANJUSAR GIDC,

TALUKA: SAVLI

DISTRICT: VADODARA

Faculty Coordinator: Prof. P.K.Shah (9033621502) / Prof A.K.Giri (9998657596)

control system sem 5

please note following points carefully

**prof M Gopal lectures on sub is given to many students. students who yet to collect it are informed to do so immediately.
** go through lect in following manner for time being
 1,2 fully
3 lect is on state variable
4 lect go upto 30 min.-test signals(impulse,step,ramp and parabolic)
5,6 lect on 2nd order system ,go fully
7 go from 25 min to 43 min.(on PID ckts)
8,9 skip for time being
10 bloc dia basic-important
11 block dia example,signal flow graph and maison gain formula-important
12 to 18 on modelling, skip for time being
19,20- on 2nd order system -important

Notice for power electronics-1

Sem.5 students are informed to bring circuit diagram and components for "triggering and commutation circuit for SCR". Make a group of 10 students according to sequence of roll list.Verify the circuit and its component with respective Lab. Teacher.

The circuit as well as power point presentation submission will be on 16/09/2016.

3 rd sem,electrical,circuit and network-practical no 1 and 2 .

click here for the practical 1 and 2

Scholarship program of Siemens Ltd for maritorious students with under privileged families(For first Year students only)

Siemens  Ltd is planning to start Scholarship Program for Engineering students. (For first Year students only) .The objective is to support and promote engineering education amongst meritorious students from less privileged families. 

Under this initiative, Siemens would offer a limited number of Scholarships by providing financial support and personality development plan for students with annual family income not more than Rs. 2 lakhs. 

 They would also like to implement this program through their partner Smile Foundation. 

 Kindly contact Prof. P.K.Shah who are having less than 2 lakhs of annual family income and good academic record. Register your names  in a excel sheet provided at Software Lab PC, Ground floor, EE department. Final shortlist/selection will be generated by company only.

Prof. P.K.Shah

7th sem visit at solarism,jambusar road bharuch

please note following points

date of visit-27/7/2016
time to reach at place-10:30
address-solarism, jambusar road
sem-7th sem electrical
how to reach-   nearly 20-25km away from ABC circle, take vehicle from ABC to BYPASS then public/private vehicals are available from bypass to solar plant.

if you take own vehicle then take care in driving as many dumpers/trucks are travel in same road.

100 point activity related GTU Circular for Information(For 3rd Sem/1 st Year Students)

GTU students to leverage one of its kinds Start-up MOOC under 100 point activity system: “Six ways to graduate: Introduction to Student Start-ups” The free Massively Open Online Course (MOOC) " Six ways to graduate: introduction to Student Start-ups" is being introduced by GTU as part of the GTU Student Start-up Policy to give students an overview of the start-up ecosystem in India along with advantage of doing start-ups in college. The “Six ways to graduate” course is being offered to students of GTU for the first time in India. GTU has empanelled multiple Technology Business Incubator (TBI) /Host Institutes (HI) for benefit of its students. This MOOC by Start-up Village (www.sv.co) is the first of many such courses that other TBI's/HI's will roll out for students so that in future, students have many MOOC's to choose from.

Key Course Highlights
  No prior start-up experience is required to take the course
  Internet connection and computer is only required to learn this program
  Students can study at their own speed of understanding
  Students can finish the course in approximately 16 weeks. Average of 4 hours of study per week is suggested.
  Students have to take this program individually.
 There will be 10 chapters in this program.
 Course will explain how students can graduate using SIX WAYS if they create a start-up in college apart from only conventional way of getting a degree from university
 At the end of each chapter, there will be a Multiple Choice Questionnaire for assessing the learning from each chapter
  Students can take multiple choice questions any number of times till they understand it in detail and are able to successfully attempt the questions.
 The objective of test is not to score but to ensure students have understood the chapters well.
 All students will get digital completion certificates after successful completion of this program students can earn 9 points under MOOC program in 100 point activity system introduced by GTU.
  Students who are then interested in creating start-ups can join any of the GTU empanelled Incubators.

All 3rd Semester Students are required to register in the link given below, for participating in this program by date 31.07.2016. http://gtu.ac.in/Mooc.aspx

Other students beyond 3rd Semester who do not avail the 100 point activity System can also take up this MOOC.

For any query kindly connect at: 100activitypoints@gtu.edu.in

Industrial Visit Planned for Odd Semester,Electrical Department (For the month July/August 2016)

Industrial Visit Planned for Odd Semester,Electrical Department (For the month July/August  2016)
Name of the Company/Plant	Semester	Date of Visit	Maximum Students	Location
KP SOLARISM	7	27/07/16	100	Jambusar Road
Expel Prosys	7	30/7/16	100	Near Savli, Vadodara
Gujarat Indutrial Power Company Ltd.	7	05/08/16	55	Ranoli,Vadodara
Sardar Sarovar	3	11/8/2016	120	Kevadia Colony
Register your names for the said visit by yourself and give the final list to Prof. P.K.Shah on or before 25/07/16.
List shall include following details as mentioned below
Enrollment No	Name	Contact No	Semester	Email	Sign
Contact Prof.P.K.Shah for more details regarding schedule,timings, contact, address etc.
Prof. P.K.Shah

Notice for 100 point activity for 3rd Semester Students

 All 3rd semester students are  required to register in the below given link,

http://gtu.ac.in/Mooc.aspx

for participating in following program

"Six Way to Graduate :Introduction to student Start-ups"

This is free Massively Open Online Course (MOOC)  being introduce by GTU

This program will help you to earn points under 100 point Activity

Last Date for Registration is 31/07/2016 

Design Engineering - I-A (3rd Sem)

Submit the information of your Group here:Click Here

The last date of submission of your group information is 26-8-16, Tuesday.

EXAMPLE DATA FOR 5 TH SEM- SUB EED

CLICK HERE FOR DATA FOR 1-PH TRANSFORMER,BALLST AND DRAWING SHEETS

Deadlines for fees for new Term(SEM 3,5,7, Electrical)

Seminar on 25/7/2016 for Final Year Students(All branch) at admin building seminar hall

There has been one seminar  organised on dt. 25/7/2016, Monday, 11:30 AM on wards at our seminar hall,admin building for all final year students.

Theme of this seminar:

(1) Resume building (2) how to crack GD/ PI (3) Transactional analysis."

Timing would be from 11.30am to 1.00pm. 

This seminar is sponsored by,

Mr.Pradeep Shukla

IBS Business School

208, World trade center, opp. BBC tower, Sayajigunj, Baroda - 390005

Opening of new Adhar Card from Government(For all semmester of Electrical)

Notice

All the students of electrical department (SEM-1,3,5,7) are hereby informed to open new adhar card and submit a copy to Electrical department on or before 28/07/2016.


Prof.Y.R.Pandya
electrical department
GEC, BHARUCH

5 th sem ,electrical , sub: EED ,examples for practical 1

All the students of 5 th sem are here with instructed to complete the Examples given below in to file up to  the next week for the subject EED. 2150904.

PRACTICAL 1

Design of Field Regulators. 

(a)   For d.c shunt motor:

(1)   A  250 V, d.c. shunt motor with a normal speed of 600 rpm takes shunt field current of  2 Amp when running light. If the speed of the motor is to be raised to 1200 rpm in increments of 150 rpm, find the resistance sections of a shunt field regulator. The O.C.C of the motor at 600 rpm is as under.

Field current, Amp	0.5	1.0	1.5	2.0	2.5
EMF, Volt	80	150	210	250	275

                                         

(2)   A  250 V, d.c. shunt motor with a normal speed of 600 rpm takes shunt field current of  2 Amp when running light. If the speed of the motor is to be raised to 1200 rpm in increments of 150 rpm, find the resistance sections of a shunt field regulator. The O.C.C of the motor at 600 rpm is as under.

Field current, Amp	0.4	0.8	1.2	1.5	2.0	2.4
EMF, Volt	70	137.5	187.5	225	250	270

(b)   For d.c shunt generator:

 (1)   Find the resistance of various sections of a 7 stud field regulator for a D.C. shunt generator to give an emf variation from 260 V to 200 V in equal steps. The resistance of the field is 58 Ω. The magnetization curve is given as below.

Field current, Amp	1	2	3	4	5	6
EMF, Volt	90	170	220	250	270	284

                (2)   Find the resistance of various sections of a 7 stud field regulator for a D.C. shunt generator              to give an emf variation from 260 V to 200 V in equal steps. The resistance of the field is 58                  Ω. The magnetization curve is given as below.

Field current, Amp	0.4	0.425	0.45	0.48	0.51	0.55
EMF, Volt	250	255	260	265	270	275

5th sem control system

Earlier video lectures  of prof M. Gopal was given to many students of 5 sem .Students are inform to go through lect 1 and 2.  A test based on above two lect will be conducted on Thursday (21st).


HOD electrical

FOR 5TH SEM ELECTRICAL(REGISTRATION FOR ATTENDING QEEE LECTURE SERIES)

All the 5th semester students from Electrical students are hereby informed to get register for QEEE Lecture series for the subject  "8085 and 8086 Microprocessor: Architecture, Assembly Language Programming and System Design".

Contact Prof. P.K.Shah for registering. Registration sheet is available at EE Department, Software Lab,Ground floor Computer Lab.

Prof. P.K.Shah

GTU PROJECT MONITORING SYSTEM HAS BEEN STARTED FOR PROJECT REGISTRATION FOR STUDENTS AND TEAM. LAST DAY IS 28TH JULY

Guidelines for Design Engineering (DE)

New Guidelines (Provided by GTU) : Click Here

DE-1A- 3rd Semester Course Abstract: Click Here

DE-1B- 4th Semester Course Abstract:Click Here

DE-2A- 5th Semester Course Abstract: Click Here

DE-2B- 6th Semester Course Abstract: Click Here

GOVERNMENT ENGINEERING COLLEGE,BHARUCH

ELECTRICAL DEPARTMENT(7^TH SEM),ODD TERM-2016-17                          SUB: Design of AC Machine(DACM)(2170909)- LAB

Design problems

                   

(1)    Design a 5HP, 440v, 50Hz, 1500rpm, 3-ф squirrel cage induction motor. Assume that: specific magnetic loading=0.46wb/m2, specific electric loading=22000ac/m, Efficiency=83%, power factor=0.84, stator winding factor=0.955. Suggest for cheap design.

(2)    Design a 30HP, 440V, 50Hz, 1000rpm,3-ф squirrel cage induction motor. Assume that: specific magnetic loading=0.45wb/m2, specific electric loading=25000ac/m, Efficiency=86%, power factor=0.87, stator winding factor=0.955. Suggest for overall good design.

(3)    Design a 10HP, 440V, 3-Phase, 4-pole, 50Hz squirrel cage induction motor which is to be started using a star-delta starter. Assume:-Average flux density in the gap=0.45wb/m2, Ampere conductors per meter=23000, efficiency=0.85, Power factor=0.84, stator winding factor=0.955. Choose the main dimension to give an overall good design.

(4)    Design a 5HP, 440v, 50Hz, 1500rpm, 3-ф squirrel cage induction motor. Assume that: specific magnetic loading=0.44wb/m2, specific electric loading=24000ac/m, Efficiency=83%, power factor=0.84, stator winding factor=0.955. Suggest for cheap design.

(5)    Design a 15HP, 440V, 3-Phase, 4-pole, 50Hz squirrel cage induction motor which is to be started using a star-delta starter. Assume:-Average flux density in the gap=0.42wb/m2, Ampere conductors per meter=26000, efficiency=0.84, Power factor=0.84, stator winding factor=0.955. Choose the main dimension for good power factor.

(6)    Design a 20HP, 440V, 3-Phase, 6-pole, 50Hz squirrel cage induction motor which is to be started using a star-delta starter. Assume:-Average flux density in the gap=0.42wb/m2, Ampere conductors per meter=26000, efficiency=0.87, Power factor=0.86, stator winding factor=0.955. Choose the main dimension for good Efficiency.

(7)    Design a 15HP, 440v, 50Hz, 1500rpm, 3-ф squirrel cage induction motor. Assume that: specific magnetic loading=0.44wb/m2, specific electric loading=24000ac/m, Efficiency=83%, power factor=0.84, stator winding factor=0.955. Suggest for cheap design.

(8)    Design a 10HP, 440V, 3-Phase, 4-pole, 50Hz squirrel cage induction motor which is to be started using a star-delta starter. Assume:-Average flux density in the gap=0.42wb/m2, Ampere conductors per meter=26000, efficiency=0.84, Power factor=0.84, stator winding factor=0.955. Choose the main dimension for good power factor.

(9)    Design a 30HP, 440V, 3-Phase, 4-pole, 50Hz squirrel cage induction motor which is to be started using a star-delta starter. Assume:-Average flux density in the gap=0.41wb/m2, Ampere conductors per meter=23000, efficiency=0.85, Power factor=0.84, stator winding factor=0.955. Choose the main dimension to give an overall good design

NOTE : (1)Draw the parts of induction motor in sheet as per the dimensions calculated from the above                         problem.

                (2)Take one problem from above as per Batch A1-1,A2-2,A3-3,A4-4,B1-5,B2-6,B3-7,B4-8 & B5-9.

3 and 7 sem students attendance

this is to inform 3 sem and 7 sem students that so many students are still absent even though academic term is already commenced.strict action will be taken if student is fail to full fill minimum attendance criteria.
             from next week dept. is starting to contact your parents regarding absenteeism.

                                                                     HOD ELECTRICAL

CLICK ON THE TIME TABLE- 3 RD SEM DIV A AND B

TIME TABLE - 3 RD SEM DIV B

TIME TABLE - 3 RD SEM DIV A

For final year student regarding project

https://drive.google.com/file/d/0B5C3uSpGTqZ7czdWVlVpdGM0TkE/view?usp=sharingAll the final year student is hereby informed that you need to finalize your project title and guide by 13/7/16. Herewith I have  attached one form to be filled by you and submit it to me on or before 7/7/16.
FOR FURTHER DETAIL PLEASE CONTACT PROF A.A.PATEL

Regarding availability of provisional certificates to passed out 8th semester students (2016)

All the students of recently concluded 8th semester examination are hereby informed that they will get their provisional degree certificates from 7th July ...

TAKE NOTE AND SUBMIT BOOKS IN LIBRARY

For Final Year Electrical Students(Regarding Project)

For Final Year Electrical Students are hereby informed to remain present for Introductory presentation regarding topic of their Final Year Project on 07/03/16.  Students shall also present about training taken by them  during vacation period. Before that, all the students must form a project groups and register their names by 05/07/16.

Prof. P.K.Shah

For WiFi Internet Access for student of Electrical Department

All the students of Electrical Engineering department is informed to register their MAC address on the below link for WiFi Access. After the registration student ID can be made active.

Link.  www.gecbharuch.com